Reproducibility and repeatability in tensiometry

Authors

DOI:

https://doi.org/10.5902/2179460X85536

Keywords:

Critical micelle concentration, Ring tensiometer, Tensiometry, Vegetable oils, Statistical analysis

Abstract

Flotation is a physical-chemical process in which there is selective hydrophobization of particles and subsequent capture of these hydrophobic particles by bubbles. Critical micelle concentration (cmc) is an important parameter in this process, as its value supports the selection of the appropriate concentration of reagents. One of the apparatuses for such measurement is the Du Noüy ring tensiometer. In this work, the repeatability and statistical reproducibility (R&R) parameter for tensiometry of saponified solutions of vegetable oils used as anionic collectors in mineral flotation was analyzed. The mean value-amplitude method was used, with two operators and three oils studied. The cmc results for both operators showed very close values, with mango and palm oils showing approximately 35 mN/m, while copaiba oil resulted in an approximate cmc value of 46 mN/m. These values resulted in an R&R% of 5.07 % and number of distinct categories (ndc) of 27.8, indicating reliability in the measurements. Given the simplicity of the method, it can be directed towards a wide range of studies.

Downloads

Download data is not yet available.

Author Biographies

Felipe de Orquiza Milhomem, Universidade Federal de Mato Grosso

Graduated in Mining and Environmental Engineering from the Universidade Federal do Pará (UFPA), with a master's and doctorate in Mineral Engineering from the Universidade Federal de Ouro Preto (UFOP). Professor in the Mining Engineering course at the Universidade Federal do Mato Grosso (UFMT).

Bruna de Oliveira Gomes, Universidade Federal de Catalão

Bachelor's degree in Mining Engineering, Master's degree in Mineral Engineering from the Universidade Federal de Ouro Preto (UFOP), and PhD candidate in Materials Science and Engineering from the Universidade Federal de Catalão (UFCAT).

José Aurélio Medeiros da Luz, Universidade Federal de Ouro Preto

Bachelor's degree in Mining Engineering from the Universidade Federal de Ouro Preto (UFOP), Master's and Doctorate degrees in Metallurgical and Mining Engineering from the Universidade Federal de Minas Gerais (UFMG).

Higor Vinícius Lopes Guedes, Vale S.A., Nova Lima, MG

Bachelor's degree in Mining Engineering from the Universidade Federal de Ouro Preto (UFOP). Mining engineering intern at Vale S.A.

References

Action, P. Repetitividade e reprodutibilidade. (2020, 20 de março). Recuperado de: http://www.portalaction.com.br/analise-dos-sistemas-de-medicao/24-repetitividade-e-reprodutibilidade

Andrade, H. M., Viana, J. H. M., Donagemma, G. K., Paz, L. F., & de Melo, B. M. (2011). Avaliação da repetitividade e reprodutibilidade para cálculo de incerteza na análise granulométrica. Anais do XXXIII Congresso Brasileiro de Ciência Do Solo Biologia Do Solo, Uberlândia, MG.

Araújo, A. C., Peres, A. E. C., Viana, P. R. M., & Oliveira, J. F. (2013). Flotação de minérios de ferro. In A. P. Chaves (Ed.), Teoria e prática do tratamento de minérios: a flotação no brasil (Volume 4, 3a ed., pp. 354–367). Oficina de Textos.

Benedetto, F. E., Zolotucho, H., & Prado, M. O. (2015). Critical assessment of the surface tension determined by the maximum pressure bubble method. Materials Research, 18(1), 9-14. https://doi.org/10.1590/1516-1439.232513

Borsato, D., Moreira, I., & Galão, O. F. (2004). Detergentes naturais e sintéticos: um guia técnico (2a ed.). Editora da Universidade Estadual de Londrina: EDUEL.

Braga, A. S., Souza Pinto, T. C., Matai, P. H. L. S., & Leal Filho, L. S. (2015). Determinação da concentração micelar crítica e a de coalescência de reagentes de flotação. Anais do XXVI Encontro nacional de tratamento de minérios e metalurgia extrativa, Poços de Caldas-MG.

Bulatovic, S. M. (2007). Handbook of flotation reagents: chemistry, theory and practice (vol. 1: flotation of sulfide ores). Elsevier.

Butt, H. J., Graf, K., & Kappl, M. (2003). Physics and chemistry of interfaces. Wiley-VCH.

Caires, L. G., & Brandão, P. R. G. (1992). Óleos vegetais saponificados na flotação de um minério fosfático. Associação Brasileira de Tecnologia Mineral, 1, 65–81.

Chui, Q. S. H., Barros, C. B. de, & Silva, T. D. da. (2009). Parâmetros R e R obtidos de programa interlaboratorial - como usá-los. Química Nova, 32(8), 2209–2213. https://doi.org/10.1590/S0100-40422009000800037

Chupa, J., Misner, S., & G. A. Smith. (2012). Soap, fatty acids, and synthetic detergents. In J. A. Kent (ed.), Handbook of industrial chemistry and biotechnology (12th ed., pp. 1098–1140). Springer Science & Business Media.

Du Noüy, P. L. (1919). A new apparatus for measuring surface tension. The Journal of General Physiology, 1(5), 521–524. https://doi.org/10.1085/jgp.1.5.521

Erhan, S. Z. (2005). Industrial uses of vegetable oil. AOCS publishing.

Feng, C., Janssen, H., Feng, Y., & Meng, Q. (2015). Hygric properties of porous building materials: Analysis of measurement repeatability and reproducibility. Building and Environment, 85, 160–172. https://doi.org/10.1016/j.buildenv.2014.11.036

Fonseca, H., & Gutierrez, L. E. (1974). Composição em ácidos graxos de óleos vegetais e gorduras animais. Anais da Escola Superior de Agricultura Luiz de Queiroz, 31, 485–490. https://doi.org/10.1590/S0071-12761974000100038

Freud, B. B., & Freud, H. Z. (1930). A theory of the ring method for the determination of surface tension. Journal of the American Chemical Society, 52(5), 1772–1782.

Guay, F., & Bisaillon, S. (1983). Validation of a mathematical model using the computer for the evaluation of different parameters related to interfaces of air/water and soyabean oil/water systems. Journal of Colloid and Interface Science, 93(1), 25–32. https://doi.org/10.1016/0021-9797(83)90380-6

Harkins, W. D., & Jordan, H. F. (1930). A method for the determination of surface and interfacial tension from the maximum pull on a ring. Journal of the American Chemical Society, 52(5), 1751–1772.

Hu, D. L., Chan, B., & Bush, J. W. M. (2003). The hydrodynamics of water strider locomotion. Nature, 424(6949), 663–666.

Lima, R. M. F., & Luz, J. A. M. (2007). Mobilidade eletroforética. In J. A. Sampaio, S. C. A. França, & P. F. A. Braga (Eds.), Tratamento de minérios: práticas laboratoriais (pp. 505-530). CETEM/MCT.

Luz, J. A. M. (2015) Flotation of iron ore. In G. E. Totten, & R. Colas. (Org.), Encyclopedia of iron, steel, and their alloys (v. 2, p. 1249-1288). Taylor & Francis Group.

Luz, J. A. M., & Lima, R. M. F. (2007). Medida da tensão superficial. In J. A. Sampaio, S. C. A. França, & P. F. A. Braga (Eds.), Tratamento de Minérios: práticas laboratoriais (pp. 473–488). CETEM/MCT.

Luz, J. A. M., & Soares Júnior, A. Interfacial tension from profile of the pendant drop versus Du Noüy’s Method. (2012). In Proceedings of XIIIth International Mineral Processing Symposium, (pp. 297–303).

Macy, R. (1935). Surface tension by the ring method. Applicability of the du Nouy apparatus. Journal of Chemical Education, 12(12), 573-576.

Mandel, J. Repeatability and reproducibility. (1972). Journal of Quality Technology, 4(2), 74–85. https://doi.org/10.1080/00224065.1972.11980520

Maniasso, N. Ambientes micelares em química analítica. (2001) Química Nova, 24, 87-93. https://doi.org/10.1590/S0100-40422001000100015

Masutani, G., & Stenstrom, M. K. (1984). A Review of surface tension measuring techniques, surfactants, and their implications for oxygen transfer in waste water treatment plants. Water Research Program, School of Engineering and Applied Science, University of California: Los Angeles, CA, USA.

Meissner, H. P., & Michaels, A. S. (1949). Surface tension of pure liquids and liquid mixtures. Industrial Engineering Chemistry, 41(12), 2782–2787.

Melo, J. C. S., Pinheiro, B. C. A., & Barbosa, E. C. (2017). O parâmetro R&R e suas formas de obtenção: uma revisão de literatura. Sigmae, 5, 12–26.

MSA. (2010). Measurement System Analysis - Reference manual (4th ed.).

Mukerjee, P. & Mysels, K. J. (2021, 10 de março). Critical micelle Concentration of Aqueous Surfactant Systems. National Bureau of Standard (NSRDS‐NBS 36), Washington, 1971. 227 p. Recuperado de: https://srd.nist.gov/NSRDS/NSRDS-NBS361.pdf

Oliveira, J. A., Luz, J. A. M. Da, & Ferreira, E. E. (2006). Grau de saponificação de óleos vegetais na flotação seletiva de apatita de minério carbonatítico. Rem: Revista Escola de Minas, 59(4), 385–390. https://doi.org/10.1590/S0370-44672006000400006

Pedott, A. H., & Fogliatto, F. S. (2012). Estudos de repetitividade e reprodutividade para dados funcionais. Produção, 23(3), 548–560. https://doi.org/10.1590/S0103-65132012005000087

Rabóczkay, T. (2016). Físico-química de interfases. Edusp.

Rao, S. R. & Leja, J. (2004). Surface chemistry of froth flotation (volume I). Kluwer Academic.

Reis, J. L. M., Araújo, A. C. A., & Rodrigues, O. M. S. (2017). Aplicabilidade do método do anel de Du Noüy para realização de medidas de tensão superficial de soluções do surfactante dodecilamina. Anais do XXVII Encontro Nacional de Tratamento de Minérios e Metalurgia Extrativa, Belém-PA.

Rocha, W. R. (2001). Interações intermoleculares. Cadernos Temáticos de Química Nova na Escola, 4, 31-36.

Román, F. L., Faro, J., & Velasco, S. (2001). A simple experiment for measuring the surface tension of soap solutions. American Journal of Physics, 69(8), 920–921.

Santos, M. S. (2014). Teoria de micelização: propriedades de soluções de surfactantes via minimização da energia livre de Gibbs (Tese de Doutorado). COPPE/UFRJ, Rio de Janeiro, Brasil.

Sharma, A. K., Saxena, M., & Sharma, R. (2018). Surface active properties and micellar features of copper soaps derived from various edible oils. Open Chemistry Journal, 5, 119-133. http://dx.doi.org/10.2174/1874842201805010119

Shaw, D. J. (1992). Introduction to colloid & surface chemistry (4th ed.). Butterworth Heinemann.

Soares Maia, J. G., Varejão, M. J. C., Filho, W. W., Mourão, A. P., Craveiro, A. A., & Alencar, J. W. (1978). Composição e oxidação do óleo de uma espécie de Copaifera. Acta Amazonica, 8(4), 705.

Sullivan, D. C., Obuchowski, N. A., Kessler, L. G., Raunig, D. L., Gatsonis, C., Huang, E. P., Kondratovich, M., Mcshane, L. M., Reeves, A. P., Barboriak, D. P., Guimaraes, A. R., & Wahl, R. L. (2015). Metrology standards for quantitative imaging biomarkers. Radiology, 277(3), 813–825. https://doi.org/10.1148/radiol.2015142202

Szyszkowski, B. V. (1908). Experimentelle Studien über kapillare Eigenschaften der wässerigen Lösungen von Fettsäuren. Zeitschrift für physikalische Chemie, 64(1), 385-414.

Vieira, P. A. F., Queiroz, J. H., Vieira, B. C., Mendes, F. Q., Barbosa, A. A., Muller, E. S., Sant’ana, R. C. O., & Moraes, G. H. K. (2009). Caracterização química do resíduo do processamento agroindustrial da manga (Mangifera indica L.) var. Ubá. Alimentos e Nutrição, 20(4), 617–623.

Wrzochal, M., & Adamczak, S. (2019). Application of a gage R&R study in evaluation of rolling bearing measurement system accuracy. Transportation Research Procedia, 40, 934–939. https://doi.org/10.1016/j.trpro.2019.07.131

Zhao, X., Xie, F., Fan, J., Liu, D., Huang, J., & Chen, S. (2018). Evaluation on Dorsey method in surface tension measurement of solder liquids containing surfactants. International Journal of Thermophysics, 39(6), 76.

Downloads

Published

2026-07-14

Most read articles by the same author(s)